[PATCH 2/2] ddraw/tests: Don't insist on a different refresh rate if no refresh rate was requested.

[Stefan Dösinger]

d4fdb1f62cf5 broke test_cursor_clipping by accident. It added a requirement
that width, height and refresh rate are different from the old mode, but
test_cursor_clipping does not use DDEDM_REFRESHRATES, so all refresh rates
are 0.

Signed-off-by: Stefan Dösinger <stefan at codeweavers.com>

---

Possibly the logical AND should be logical OR, i.e. one of the properties
differs and not all of them?
---
 dlls/ddraw/tests/ddraw2.c | 2 +-
 dlls/ddraw/tests/ddraw4.c | 2 +-
 dlls/ddraw/tests/ddraw7.c | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/dlls/ddraw/tests/ddraw2.c b/dlls/ddraw/tests/ddraw2.c
index 8a6c4b41ac1..625776c652c 100644
--- a/dlls/ddraw/tests/ddraw2.c
+++ b/dlls/ddraw/tests/ddraw2.c
@@ -15116,7 +15116,7 @@ static HRESULT CALLBACK find_different_mode_callback(DDSURFACEDESC *surface_desc
 
     /* See comment in ddraw7 about the frequency. */
     if (surface_desc->dwWidth != param->old_width && surface_desc->dwHeight != param->old_height &&
-            !compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1))
+            (!compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1) || !param->old_frequency))
     {
         param->new_width = surface_desc->dwWidth;
         param->new_height = surface_desc->dwHeight;
diff --git a/dlls/ddraw/tests/ddraw4.c b/dlls/ddraw/tests/ddraw4.c
index c229ab66341..9b8acb674e3 100644
--- a/dlls/ddraw/tests/ddraw4.c
+++ b/dlls/ddraw/tests/ddraw4.c
@@ -18153,7 +18153,7 @@ static HRESULT CALLBACK find_different_mode_callback(DDSURFACEDESC2 *surface_des
 
     /* See comment in ddraw7 about the frequency. */
     if (surface_desc->dwWidth != param->old_width && surface_desc->dwHeight != param->old_height &&
-            !compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1))
+            (!compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1) || !param->old_frequency))
     {
         param->new_width = surface_desc->dwWidth;
         param->new_height = surface_desc->dwHeight;
diff --git a/dlls/ddraw/tests/ddraw7.c b/dlls/ddraw/tests/ddraw7.c
index 18ebf849391..84789e8f177 100644
--- a/dlls/ddraw/tests/ddraw7.c
+++ b/dlls/ddraw/tests/ddraw7.c
@@ -18427,7 +18427,7 @@ static HRESULT CALLBACK find_different_mode_callback(DDSURFACEDESC2 *surface_des
      * set 60hz in the advanced display properties manually. Usually the restriction to one refresh
      * rate applies to laptop panels. */
     if (surface_desc->dwWidth != param->old_width && surface_desc->dwHeight != param->old_height &&
-            !compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1))
+            (!compare_uint(surface_desc->dwRefreshRate, param->old_frequency, 1) || !param->old_frequency))
     {
         param->new_width = surface_desc->dwWidth;
         param->new_height = surface_desc->dwHeight;
-- 
2.34.1